#define IPMI_BMC_CHANNEL 0xf
#define IPMI_NUM_CHANNELS 0x10
+/*
+ * Used to signify an "all channel" bitmask. This is more than the
+ * actual number of channels because this is used in userland and
+ * will cover us if the number of channels is extended.
+ */
+#define IPMI_CHAN_ALL (~0)
+
/*
* A raw IPMI message without any addressing. This covers both
code as the first byte of the incoming data, unlike a response. */
+/*
+ * Modes for ipmi_set_maint_mode() and the userland IOCTL. The AUTO
+ * setting is the default and means it will be set on certain
+ * commands. Hard setting it on and off will override automatic
+ * operation.
+ */
+#define IPMI_MAINTENANCE_MODE_AUTO 0
+#define IPMI_MAINTENANCE_MODE_OFF 1
+#define IPMI_MAINTENANCE_MODE_ON 2
#ifdef __KERNEL__
*/
#include <linux/list.h>
#include <linux/module.h>
-
-#ifdef CONFIG_PROC_FS
+#include <linux/device.h>
#include <linux/proc_fs.h>
-extern struct proc_dir_entry *proc_ipmi_root;
-#endif /* CONFIG_PROC_FS */
/* Opaque type for a IPMI message user. One of these is needed to
send and receive messages. */
/*
* When commands come in to the SMS, the user can register to receive
- * them. Only one user can be listening on a specific netfn/cmd pair
+ * them. Only one user can be listening on a specific netfn/cmd/chan tuple
* at a time, you will get an EBUSY error if the command is already
* registered. If a command is received that does not have a user
* registered, the driver will automatically return the proper
- * error.
+ * error. Channels are specified as a bitfield, use IPMI_CHAN_ALL to
+ * mean all channels.
*/
int ipmi_register_for_cmd(ipmi_user_t user,
unsigned char netfn,
- unsigned char cmd);
+ unsigned char cmd,
+ unsigned int chans);
int ipmi_unregister_for_cmd(ipmi_user_t user,
unsigned char netfn,
- unsigned char cmd);
+ unsigned char cmd,
+ unsigned int chans);
+
+/*
+ * Go into a mode where the driver will not autonomously attempt to do
+ * things with the interface. It will still respond to attentions and
+ * interrupts, and it will expect that commands will complete. It
+ * will not automatcially check for flags, events, or things of that
+ * nature.
+ *
+ * This is primarily used for firmware upgrades. The idea is that
+ * when you go into firmware upgrade mode, you do this operation
+ * and the driver will not attempt to do anything but what you tell
+ * it or what the BMC asks for.
+ *
+ * Note that if you send a command that resets the BMC, the driver
+ * will still expect a response from that command. So the BMC should
+ * reset itself *after* the response is sent. Resetting before the
+ * response is just silly.
+ *
+ * If in auto maintenance mode, the driver will automatically go into
+ * maintenance mode for 30 seconds if it sees a cold reset, a warm
+ * reset, or a firmware NetFN. This means that code that uses only
+ * firmware NetFN commands to do upgrades will work automatically
+ * without change, assuming it sends a message every 30 seconds or
+ * less.
+ *
+ * See the IPMI_MAINTENANCE_MODE_xxx defines for what the mode means.
+ */
+int ipmi_get_maintenance_mode(ipmi_user_t user);
+int ipmi_set_maintenance_mode(ipmi_user_t user, int mode);
/*
* Allow run-to-completion mode to be set for the interface of
the watcher list. So you can add and remove users from the
IPMI interface, send messages, etc., but you cannot add
or remove SMI watchers or SMI interfaces. */
- void (*new_smi)(int if_num);
+ void (*new_smi)(int if_num, struct device *dev);
void (*smi_gone)(int if_num);
};
#define IPMICTL_UNREGISTER_FOR_CMD _IOR(IPMI_IOC_MAGIC, 15, \
struct ipmi_cmdspec)
+/*
+ * Register to get commands from other entities on specific channels.
+ * This way, you can only listen on specific channels, or have messages
+ * from some channels go to one place and other channels to someplace
+ * else. The chans field is a bitmask, (1 << channel) for each channel.
+ * It may be IPMI_CHAN_ALL for all channels.
+ */
+struct ipmi_cmdspec_chans
+{
+ unsigned int netfn;
+ unsigned int cmd;
+ unsigned int chans;
+};
+
+/*
+ * Register to receive a specific command on specific channels. error values:
+ * - EFAULT - an address supplied was invalid.
+ * - EBUSY - One of the netfn/cmd/chans supplied was already in use.
+ * - ENOMEM - could not allocate memory for the entry.
+ */
+#define IPMICTL_REGISTER_FOR_CMD_CHANS _IOR(IPMI_IOC_MAGIC, 28, \
+ struct ipmi_cmdspec_chans)
+/*
+ * Unregister some netfn/cmd/chans. error values:
+ * - EFAULT - an address supplied was invalid.
+ * - ENOENT - None of the netfn/cmd/chans were found registered for this user.
+ */
+#define IPMICTL_UNREGISTER_FOR_CMD_CHANS _IOR(IPMI_IOC_MAGIC, 29, \
+ struct ipmi_cmdspec_chans)
+
/*
* Set whether this interface receives events. Note that the first
* user registered for events will get all pending events for the
#define IPMICTL_GET_TIMING_PARMS_CMD _IOR(IPMI_IOC_MAGIC, 23, \
struct ipmi_timing_parms)
+/*
+ * Set the maintenance mode. See ipmi_set_maintenance_mode() above
+ * for a description of what this does.
+ */
+#define IPMICTL_GET_MAINTENANCE_MODE_CMD _IOR(IPMI_IOC_MAGIC, 30, int)
+#define IPMICTL_SET_MAINTENANCE_MODE_CMD _IOW(IPMI_IOC_MAGIC, 31, int)
+
#endif /* __LINUX_IPMI_H */
git://git.onelab.eu / linux-2.6.git / blobdiff