#ifndef MMC_MMC_PROTOCOL_H
#define MMC_MMC_PROTOCOL_H
-/* Standard MMC commands (3.1) type argument response */
+/* Standard MMC commands (4.1) type argument response */
/* class 1 */
#define MMC_GO_IDLE_STATE 0 /* bc */
#define MMC_SEND_OP_COND 1 /* bcr [31:0] OCR R3 */
#define MMC_ALL_SEND_CID 2 /* bcr R2 */
#define MMC_SET_RELATIVE_ADDR 3 /* ac [31:16] RCA R1 */
#define MMC_SET_DSR 4 /* bc [31:16] RCA */
+#define MMC_SWITCH 6 /* ac [31:0] See below R1b */
#define MMC_SELECT_CARD 7 /* ac [31:16] RCA R1 */
+#define MMC_SEND_EXT_CSD 8 /* adtc R1 */
#define MMC_SEND_CSD 9 /* ac [31:16] RCA R2 */
#define MMC_SEND_CID 10 /* ac [31:16] RCA R2 */
#define MMC_READ_DAT_UNTIL_STOP 11 /* adtc [31:0] dadr R1 */
/* class 8 */
/* This is basically the same command as for MMC with some quirks. */
#define SD_SEND_RELATIVE_ADDR 3 /* bcr R6 */
+#define SD_SWITCH 6 /* adtc [31:0] See below R1 */
/* Application commands */
#define SD_APP_SET_BUS_WIDTH 6 /* ac [1:0] bus width R1 */
+#define SD_APP_SEND_NUM_WR_BLKS 22 /* adtc R1 */
#define SD_APP_OP_COND 41 /* bcr [31:0] OCR R3 */
#define SD_APP_SEND_SCR 51 /* adtc R1 */
+/*
+ * MMC_SWITCH argument format:
+ *
+ * [31:26] Always 0
+ * [25:24] Access Mode
+ * [23:16] Location of target Byte in EXT_CSD
+ * [15:08] Value Byte
+ * [07:03] Always 0
+ * [02:00] Command Set
+ */
+
+/*
+ * SD_SWITCH argument format:
+ *
+ * [31] Check (0) or switch (1)
+ * [30:24] Reserved (0)
+ * [23:20] Function group 6
+ * [19:16] Function group 5
+ * [15:12] Function group 4
+ * [11:8] Function group 3
+ * [7:4] Function group 2
+ * [3:0] Function group 1
+ */
+
/*
MMC status in R1
Type
#define CSD_STRUCT_VER_1_0 0 /* Valid for system specification 1.0 - 1.2 */
#define CSD_STRUCT_VER_1_1 1 /* Valid for system specification 1.4 - 2.2 */
-#define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 */
+#define CSD_STRUCT_VER_1_2 2 /* Valid for system specification 3.1 - 3.2 - 3.31 - 4.0 - 4.1 */
+#define CSD_STRUCT_EXT_CSD 3 /* Version is coded in CSD_STRUCTURE in EXT_CSD */
#define CSD_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.2 */
#define CSD_SPEC_VER_1 1 /* Implements system specification 1.4 */
#define CSD_SPEC_VER_2 2 /* Implements system specification 2.0 - 2.2 */
-#define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 */
+#define CSD_SPEC_VER_3 3 /* Implements system specification 3.1 - 3.2 - 3.31 */
+#define CSD_SPEC_VER_4 4 /* Implements system specification 4.0 - 4.1 */
+
+/*
+ * EXT_CSD fields
+ */
+
+#define EXT_CSD_BUS_WIDTH 183 /* R/W */
+#define EXT_CSD_HS_TIMING 185 /* R/W */
+#define EXT_CSD_CARD_TYPE 196 /* RO */
+
+/*
+ * EXT_CSD field definitions
+ */
+
+#define EXT_CSD_CMD_SET_NORMAL (1<<0)
+#define EXT_CSD_CMD_SET_SECURE (1<<1)
+#define EXT_CSD_CMD_SET_CPSECURE (1<<2)
+
+#define EXT_CSD_CARD_TYPE_26 (1<<0) /* Card can run at 26MHz */
+#define EXT_CSD_CARD_TYPE_52 (1<<1) /* Card can run at 52MHz */
+
+#define EXT_CSD_BUS_WIDTH_1 0 /* Card is in 1 bit mode */
+#define EXT_CSD_BUS_WIDTH_4 1 /* Card is in 4 bit mode */
+#define EXT_CSD_BUS_WIDTH_8 2 /* Card is in 8 bit mode */
+
+/*
+ * MMC_SWITCH access modes
+ */
+
+#define MMC_SWITCH_MODE_CMD_SET 0x00 /* Change the command set */
+#define MMC_SWITCH_MODE_SET_BITS 0x01 /* Set bits which are 1 in value */
+#define MMC_SWITCH_MODE_CLEAR_BITS 0x02 /* Clear bits which are 1 in value */
+#define MMC_SWITCH_MODE_WRITE_BYTE 0x03 /* Set target to value */
+
+/*
+ * SCR field definitions
+ */
+#define SCR_SPEC_VER_0 0 /* Implements system specification 1.0 - 1.01 */
+#define SCR_SPEC_VER_1 1 /* Implements system specification 1.10 */
+#define SCR_SPEC_VER_2 2 /* Implements system specification 2.00 */
/*
* SD bus widths
git://git.onelab.eu / linux-2.6.git / blobdiff