-Post-v2.0.0
+Post-v2.2.0
---------------------
+ - OpenFlow 1.1, 1.2, and 1.3 are now enabled by default in
+ ovs-vswitchd.
+ - Linux kernel datapath now has an exact match cache optimizing the
+ flow matching process.
+ - Datapath flows now have partially wildcarded tranport port field
+ matches. This reduces userspace upcalls, but increases the
+ number of different masks in the datapath. The kernel datapath
+ exact match cache removes the overhead of matching the incoming
+ packets with the larger number of masks, but when paired with an
+ older kernel module, some workloads may perform worse with the
+ new userspace.
+
+v2.2.0 - xx xxx xxx
+---------------------
+ - Internal ports are no longer brought up by default, because it
+ should be an administrator task to bring up devices as they are
+ configured properly.
+ - ovs-vsctl now reports when ovs-vswitchd fails to create a new port or
+ bridge.
+ - The "ovsdbmonitor" graphical tool has been removed, because it was
+ poorly maintained and not widely used.
+ - New "check-ryu" Makefile target for running Ryu tests for OpenFlow
+ controllers against Open vSwitch. See INSTALL for details.
+ - Added IPFIX support for SCTP flows and templates for ICMPv4/v6 flows.
+ - Upon the receipt of a SIGHUP signal, ovs-vswitchd no longer reopens its
+ log file (it will terminate instead). Please use 'ovs-appctl vlog/reopen'
+ instead.
+ - Support for Linux kernels up to 3.14. From Kernel 3.12 onwards OVS uses
+ tunnel API for GRE and VXLAN.
+ - Added DPDK support.
+ - Added support for custom vlog patterns in Python
+
+
+v2.1.0 - 19 Mar 2014
+---------------------
+ - Address prefix tracking support for flow tables. New columns
+ "prefixes" in OVS-DB table "Flow_Table" controls which packet
+ header fields are used for address prefix tracking. Prefix
+ tracking allows the classifier to skip rules with longer than
+ necessary prefixes, resulting in better wildcarding for datapath
+ flows. Default configuration is to not use any fields for prefix
+ tracking. However, if any flow tables contain both exact matches
+ and masked matches for IP address fields, OVS performance may be
+ increased by using this feature.
+ * As of now, the fields for which prefix lookup can be enabled
+ are: 'tun_id', 'tun_src', 'tun_dst', 'nw_src', 'nw_dst' (or
+ aliases 'ip_src' and 'ip_dst'), 'ipv6_src', and 'ipv6_dst'.
+ (Using this feature for 'tun_id' would only make sense if the
+ tunnel IDs have prefix structure similar to IP addresses.)
+ * There is a maximum number of fields that can be enabled for any
+ one flow table. Currently this limit is 3.
+ * Examples:
+ $ ovs-vsctl set Bridge br0 flow_tables:0=@N1 -- \
+ --id=@N1 create Flow_Table name=table0
+ $ ovs-vsctl set Bridge br0 flow_tables:1=@N1 -- \
+ --id=@N1 create Flow_Table name=table1
+ $ ovs-vsctl set Flow_Table table0 prefixes=ip_dst,ip_src
+ $ ovs-vsctl set Flow_Table table1 prefixes=[]
+ - TCP flags matching: OVS now supports matching of TCP flags. This
+ has an adverse performance impact when using OVS userspace 1.10
+ or older (no megaflows support) together with the new OVS kernel
+ module. It is recommended that the kernel and userspace modules
+ both are upgraded at the same time.
- The default OpenFlow and OVSDB ports will change to
IANA-assigned numbers in a future release. Consider updating
your installations to specify port numbers instead of using the
defaults.
- OpenFlow:
* The OpenFlow 1.1+ "Write-Actions" instruction is now supported.
+ * OVS limits the OpenFlow port numbers it assigns to port 32767 and
+ below, leaving port numbers above that range free for assignment
+ by the controller.
+ * ovs-vswitchd now honors changes to the "ofport_request" column
+ in the Interface table by changing the port's OpenFlow port
+ number.
- ovs-vswitchd.conf.db.5 man page will contain graphviz/dot
diagram only if graphviz package was installed at the build time.
+ - Support for Linux kernels up to 3.11
+ - ovs-dpctl:
+ The "show" command also displays mega flow mask stats.
+ - ovs-ofctl:
+ * New command "ofp-parse-pcap" to dump OpenFlow from PCAP files.
+ - ovs-controller has been renamed test-controller. It is no longer
+ packaged or installed by default, because too many users assumed
+ incorrectly that ovs-controller was a necessary or desirable part
+ of an Open vSwitch deployment.
+ - Added vlog option to export to a UDP syslog sink.
+ - ovsdb-client:
+ * The "monitor" command can now monitor all tables in a database,
+ instead of being limited to a single table.
+ - The flow-eviction-threshold has been replaced by the flow-limit which is a
+ hard limit on the number of flows in the datapath. It defaults to 200,000
+ flows. OVS automatically adjusts this number depending on network
+ conditions.
+ - Added IPv6 support for active and passive socket communications.
v2.0.0 - 15 Oct 2013
git://git.onelab.eu / sliver-openvswitch.git / blobdiff