#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <asm/arch/pxa2xx_spi.h>
+
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
}
-static struct irqchip lubbock_irq_chip = {
+static struct irq_chip lubbock_irq_chip = {
+ .name = "FPGA",
.ack = lubbock_mask_irq,
.mask = lubbock_mask_irq,
.unmask = lubbock_unmask_irq,
};
-static void lubbock_irq_handler(unsigned int irq, struct irqdesc *desc,
- struct pt_regs *regs)
+static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
do {
if (likely(pending)) {
irq = LUBBOCK_IRQ(0) + __ffs(pending);
desc = irq_desc + irq;
- desc_handle_irq(irq, desc, regs);
+ desc_handle_irq(irq, desc);
}
pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
} while (pending);
/* setup extra lubbock irqs */
for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
set_irq_chip(irq, &lubbock_irq_chip);
- set_irq_handler(irq, do_level_IRQ);
+ set_irq_handler(irq, handle_level_irq);
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
},
};
+/* ADS7846 is connected through SSP ... and if your board has J5 populated,
+ * you can select it to replace the ucb1400 by switching the touchscreen cable
+ * (to J5) and poking board registers (as done below). Else it's only useful
+ * for the temperature sensors.
+ */
+static struct resource pxa_ssp_resources[] = {
+ [0] = {
+ .start = __PREG(SSCR0_P(1)),
+ .end = __PREG(SSCR0_P(1)) + 0x14,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_SSP,
+ .end = IRQ_SSP,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct pxa2xx_spi_master pxa_ssp_master_info = {
+ .ssp_type = PXA25x_SSP,
+ .clock_enable = CKEN3_SSP,
+ .num_chipselect = 0,
+};
+
+static struct platform_device pxa_ssp = {
+ .name = "pxa2xx-spi",
+ .id = 1,
+ .resource = pxa_ssp_resources,
+ .num_resources = ARRAY_SIZE(pxa_ssp_resources),
+ .dev = {
+ .platform_data = &pxa_ssp_master_info,
+ },
+};
+
+static int lubbock_ads7846_pendown_state(void)
+{
+ /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
+ return 0;
+}
+
+static struct ads7846_platform_data ads_info = {
+ .model = 7846,
+ .vref_delay_usecs = 100, /* internal, no cap */
+ .get_pendown_state = lubbock_ads7846_pendown_state,
+ // .x_plate_ohms = 500, /* GUESS! */
+ // .y_plate_ohms = 500, /* GUESS! */
+};
+
+static void ads7846_cs(u32 command)
+{
+ static const unsigned TS_nCS = 1 << 11;
+ lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
+}
+
+static struct pxa2xx_spi_chip ads_hw = {
+ .tx_threshold = 1,
+ .rx_threshold = 2,
+ .cs_control = ads7846_cs,
+};
+
+static struct spi_board_info spi_board_info[] __initdata = { {
+ .modalias = "ads7846",
+ .platform_data = &ads_info,
+ .controller_data = &ads_hw,
+ .irq = LUBBOCK_BB_IRQ,
+ .max_speed_hz = 120000 /* max sample rate at 3V */
+ * 26 /* command + data + overhead */,
+ .bus_num = 1,
+ .chip_select = 0,
+},
+};
+
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = -1,
&smc91x_device,
&lubbock_flash_device[0],
&lubbock_flash_device[1],
+ &pxa_ssp,
};
-static struct pxafb_mach_info sharp_lm8v31 __initdata = {
+static struct pxafb_mode_info sharp_lm8v31_mode = {
.pixclock = 270000,
.xres = 640,
.yres = 480,
.lower_margin = 0,
.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
.cmap_greyscale = 0,
+};
+
+static struct pxafb_mach_info sharp_lm8v31 = {
+ .modes = &sharp_lm8v31_mode,
+ .num_modes = 1,
.cmap_inverse = 0,
.cmap_static = 0,
.lccr0 = LCCR0_SDS,
#define MMC_POLL_RATE msecs_to_jiffies(1000)
static void lubbock_mmc_poll(unsigned long);
-static irqreturn_t (*mmc_detect_int)(int, void *, struct pt_regs *);
+static irq_handler_t mmc_detect_int;
static struct timer_list mmc_timer = {
.function = lubbock_mmc_poll,
if (LUB_IRQ_SET_CLR & (1 << 0))
mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
else {
- (void) mmc_detect_int(LUBBOCK_SD_IRQ, (void *)data, NULL);
+ (void) mmc_detect_int(LUBBOCK_SD_IRQ, (void *)data);
enable_irq(LUBBOCK_SD_IRQ);
}
}
-static irqreturn_t lubbock_detect_int(int irq, void *data, struct pt_regs *regs)
+static irqreturn_t lubbock_detect_int(int irq, void *data)
{
/* IRQ is level triggered; disable, and poll for removal */
disable_irq(irq);
mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
- return mmc_detect_int(irq, data, regs);
+ return mmc_detect_int(irq, data);
}
static int lubbock_mci_init(struct device *dev,
- irqreturn_t (*detect_int)(int, void *, struct pt_regs *),
+ irq_handler_t detect_int,
void *data)
{
/* setup GPIO for PXA25x MMC controller */
init_timer(&mmc_timer);
mmc_timer.data = (unsigned long) data;
return request_irq(LUBBOCK_SD_IRQ, lubbock_detect_int,
- SA_SAMPLE_RANDOM, "lubbock-sd-detect", data);
+ IRQF_SAMPLE_RANDOM, "lubbock-sd-detect", data);
}
static int lubbock_mci_get_ro(struct device *dev)
lubbock_flash_data[flashboot^1].name = "application-flash";
lubbock_flash_data[flashboot].name = "boot-rom";
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
}
static struct map_desc lubbock_io_desc[] __initdata = {
pxa_map_io();
iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
+ /* SSP data pins */
+ pxa_gpio_mode(GPIO23_SCLK_MD);
+ pxa_gpio_mode(GPIO25_STXD_MD);
+ pxa_gpio_mode(GPIO26_SRXD_MD);
+
/* This enables the BTUART */
pxa_gpio_mode(GPIO42_BTRXD_MD);
pxa_gpio_mode(GPIO43_BTTXD_MD);
git://git.onelab.eu / linux-2.6.git / blobdiff